Argox OS Series Spezifikationen

OS Series Desktop Barcode Printer User’s Manual II Proprietary Statement This manual contains proprietary information of Argox Informat

14 Media Compartment Release LeverPrint Head Module Release Lever Ribbon Supply Holder 15 4. Unwrap the ribbon roll pa

16 7. Put the print head module down and insert the bare core into the pick-up holder. (First snap in the left side, and then the right side.)

18 Loading Media The OS Series printers offer three different loading modes: standard, peel-off, or cutting. • Standard mode allows you to collect

20 4. Click the media hanger back into the media compartment. 5. Align the media roll to the left end. 6. Move the shield from right to left until

22 10. Put the print head module down and press down firmly until you hear a snap. 11. Close the top cover and turn on the printer or press the "

24 10. Trim the front edge of the label backing paper with scissors or a knife. 11. Lead the backing paper over the dispenser bar, then thread it back

26 15. Close the top cover and turn on the printer or press the "FEED" button if the printer is already on. Note: The "FEED" but

28 11. Close the top cover and turn on the printer or press the "FEED" button if the printer is already on. Note: The "FEED" but

30 Resetting to Factory Default Settings 1. Turn on the printer and wait for 5 or more seconds. 2. Press the "Feed" button for 10 seconds

32 Power Jack RS232 Serial Port Parallel Port Power Jack Parallel Port RS232 Serial Port OS-204 / OS-214 / OS-214Zip /

III A Letter to Our Customers Dear Customers, Congratulation on selecting an Argox OS series printer! We believe soon you will find that you have ma

34 Communicating with the Printer The bundled printer driver can be applied to all applications under Windows 98/2000/NT, and Windows XP. With this d

36 5. After the related files are copied to your system, click “Next”. 6. After the installation is complete, click “Finish”.

38 Setting Parameters After installing the driver, follow the path below to set parameters: Start → Settings→ Printers→ Label Dr.→ Properties Param

40 Output bin (Accessory setting) In the Properties menu: → Click "Paper" → Click "More Options" → Select Enable w/o cutter, pee

42 Parameters for Win 2000 Ports In the Properties menu: → Click "Ports" → Select the IO port → Click "OK" Paper sourc

44 Paper size setup In Printing Preferences: → Click tag "Layout" → Click button "Advanced" → Click "button Customize”"

46 For NT 4.0 Ports In the Properties menu: → Click "Ports" → Select IO port → Click "OK" Paper size Orientation Paper s

48 For Win XP Ports In the Properties menu: → Click "Ports" → Select the IO port → Click "OK" Paper source (Media ty

50 Paper size setup In Printing Preferences: → Click tag "Layout" → Click button "Advanced" → Click button "Customize”"

52 Troubleshooting Normally, when the printer is in not working properly, the "Power" LED blinks continuously; while printing and communica

V Troubleshooting...52 LED Diagnosis...

54 Miscellaneous If the host shows "Printer Time out" 1. Check if the communication cable (parallel or serial) is connected securely to yo

56 Caring for Your Printer After using eight rolls of label stock, clean the following areas of the printer. Note: Always switch off the power be

58 59 Technical Reference General Specifications Specification Model OS-203Model OS-204ModelOS-214Model OS-214Zip Model OS-314TT Print

60 Specification ModelOS-203Model OS-204 ModelOS-214Model OS-214 ZipModel OS-314TTMaximum label roll diameter 4.3 in.(109mm) outside diameter, 1 in.(2

62 Fonts, Bar Codes and Graphics Specification The specifications of fonts, bar codes and graphics depends on printer emulation, which is a printer p

64 Printer Programming Language Z, PPLZ (OS-214Zip) Specification Model OS-214Zip General fonts 10 resident fonts (9 bitmapped fonts and 1 scalable fo

66 Note: Pin 9 on the OS-204/214/314 and pin 1 on the OS-203 are reserved for a KDU (keyboard device unit). Do not connect these pins if you are usin

68 Parallel (Centronics) The parallel port is a standard 36-pin Centronics. Pin assignments are as follows: Pin Direction Definition Pin Direction

70 Appendix I - Installing Dispenser Kit 1. Turn off the printer power and unplug the printer. 2. Unwrap the dispenser kit and take out screws, the

72 Base Housing 12. Release the screw on the left bracket of the chassis. Base Housing Screw73 13. Unlatch the print head mo

2 Package Contents • Printer • Power Adapter • User’s Manual • CD Rom Disk • Ribbon (not included with OS-203 or OS-204) •

74 19. Click the top cover back onto the middle cover. 20. Insert the sensor connector into its receptacle on the main logic board of the base housing

76 4. Remove the whole print head assembly by releasing the 4 screws at its feet. 5. a. Mount the cutter IC (3717) to U19 on th

4 OS-203 Model AC Electrical Outlet Cord Power Adapter Barrel Connector Power Switch Power Jack 5 Getting to Know Your Printer There are five model

6 Ribbon Pick-up Holder Release Levers Media Hanger Power Switch Ribbon Supply Holder Thermal Print headPlaten Roller OS-

8 Parts and Features (OS-203, OS-204) Top Cover Power Switch H Cover Power Indicator Ready indicator Feed Button OS-203 /

10 Peel-Off Option Cutter Option White Plastic Roller Cutter OS-203 / OS-204 Models 11 Controls and Indicators The printer’s

12 Control / Indicator Function Power Switch • On: power on • Off: shut down Note: Turn power off before connecting or disconnecting cables Po