Argox A-3140 Bedienungsanleitung

A SERIE PRINTERS A-2240, A-2240E, A-2240Z, A-2240ZE, A-3140, A-3140Z User’s Manual Website: http://www.argox.com A Series User’s Manual 2

A Series User’s Manual 19 7. Turn back the print head module and then insert the bare core into the pick-up holder. (First snap in the right side,

A Series User’s Manual 21 Loading Media The Amigo Series printers offer three different loading modes: standard, peel-off, or with a cutter.  S

A Series User’s Manual 23 6. Lead the labels through the media guides with the other hand. The media guide can be adjusted centrally to fit with

A Series User’s Manual 25 8. Close the top cover and turn on the printer or press the feed button if the printer is already on.

A Series User’s Manual 27 3. Plug in the dispenser connecter. 4. Mount the dispenser module. Dispenser Connecter

A Series User’s Manual 29 7. Press down the print head module firmly until you hear a snap. 8. Close the top cover and turn on the printer or pre

A Series User’s Manual 31 Cutter Mode Note: For cutter mode you must first install the cutter and cutter baby board to J16 on the main board 1.

A Series User’s Manual 33 A Series User’s Manual 34 7. Remove the whole print head assembly by releasing the 4 screws at its feet.

A Series User’s Manual 35 9. Reattempt the print head assembly by securing the 4 screws and pull the front side of "Middle Cover" to p

A Series User’s Manual 37 Media Guides 15. Lead the label through the media guides and cutter slot. 16. Press down the print head module firmly on

A Series User’s Manual 3 anyone else involved in the creation, production, or delivery of the accompanying product (including hardware

A Series User’s Manual 39 Configuration and Configuration This section discusses calibration, printing configuration and resetting the printer to

A Series User’s Manual 41 Computer Connections Note: You must insert the power supply’s barrel connector into the power jack on the back of the p

A Series User’s Manual 43 Power Cord A Series User’s Manual 44 Ethernet 10/100 Internal Printer Server Option This connector is for E

A Series User’s Manual 45 Ethernet Status/Activity Indicators LED Status Description Both Off No Ethernet link detected Spee

A Series User’s Manual 47 Installing a Plug and Play printer driver (for USB only) 1. Turn off the printer. Plug the power cable into t

A Series User’s Manual 49 Instead of the flash prompt above, another way to install Seagull driver is to run the DriverWizard utility

A Series User’s Manual 51 7. Check all the data on the showing screen, if it is correct, click "Finish". Argox A-22

A Series User’s Manual 53 9. After driver installation is complete, click "Close". The driver should now be installed. Installed

A Series User’s Manual 55 3. Under A-2240 product selection prompt, choose Seagull Driver version and then start installation: In

A Series User’s Manual 57 5. Assign the directory to keep Seagull driver, (for example: C:\Seagull) and click "Next". A

A Series User’s Manual 5 Table of Contents Introduction... 2 Propriet

A Series User’s Manual 59 7. Select Install printer drivers and Click "Next" A Series User’s Manual

A Series User’s Manual 61 9. Select the port of the printer and click "Next". A Series User’s Manual

A Series User’s Manual 63 11. Check all the data on the showing screen, if it is correct, click "Finish". 12. Argox

A Series User’s Manual 65 14. After driver installation is complete, click "Close". The driver should now be installed. Installed prin

A Series User’s Manual 67 LED Indicators: Power and Ready LEDs blink alternately Power LED Ready LED ON OFF OFF ON Possible Problems Solutions

A Series User’s Manual 69 Miscellaneous  If the host shows "Printer Time out" 1. Check if the communication cable (serial) is connect

A Series User’s Manual 71 Caring for Your Printer Adhesives and coatings of media can over time transfer onto the printer components along the med

A Series User’s Manual 73 Special Caution: Warranty of print heads will be void if print head serial number is removed, altered, defected, or

A Series User’s Manual 75 3. Loosen the 2 screws(C) and take off COVER-TPH(79) 4. Unplug the 2 print head cables from the connectors on the old T

A Series User’s Manual 77 Technical Reference General Specifications Specification A-2240 A-2240E A-2240Z A-3140 A-3140Z Printing method Di

A Series User’s Manual 7 Getting Started Congratulations on choosing the Argox Amigo Series desktop barcode printer. This user’s manual will help

A Series User’s Manual 79 Fonts, Bar Codes and Graphics Specification The specifications of fonts, bar codes and graphics depends on the printer e

A Series User’s Manual 81 Printer Programming Language Z, PPLZ Programming Language PPLZ Internal fonts 8 (A~H) fonts with different point size. 8

A Series User’s Manual 83 Interface Specifications USB Interface This is port complies with USB 2.0 Full Speed. T Connector Terminal Pin Assig

A Series User’s Manual 85 Ethernet The following port complies with Ethernet communication. Pin Signal 1 Transmit+ 2 Transmit- 3 Rec

A Series User’s Manual 87 Printer Terminal/Host Pin 2- RxData ……… TxData Pin 3- TxData ……… RxData Pin 5- Ground ……… Ground In general, as l

A Series User’s Manual 89 4. Remove the middle cover. Slot for Extension card A Series User’s Manual 90 5. Mount the extension card to

A Series User’s Manual 9 Connecting the Power Supply Connect the power supply as below. WARNING: 1. do not operate the printer and power supp

A Series User’s Manual 11 Power Cord A Series User’s Manual 12 Getting to Know Your Printer The illustrations that follow describe the p

A Series User’s Manual 13 Ribbon Pick-up Holder Release Levers Media Hanger Ribbon Supply Holder Thermal Printhead A Series User’

A Series User’s Manual 15 Control / Indicator Function Power Switch  On: turns on normal operation  Off: turns off power Note: Turn power

A Series User’s Manual 17 Ribbon Supply Holder Media Compartment Release Lever Print Head Module A Series